How to make turkey box call

how to make turkey box call

Turkey Box Call TDE 110

Feb 27,  · SCDNR's South Carolina Wildlife Magazine talks with John Tanner of Hemingway, South Carolina about turkey calls. Follow along as he shows you how to make a b. Apr 10,  · how to make a turkey box call. I say um uh a lot sorry:P The audio may also be a little soft. I made a second video with the measurements of a few other cal.

A box call can make a remarkable variety of sounds that mimic those of a wild turkey. The call is a simple wooden box with a paddle-shaped top what is supravalvular aortic stenosis, moved back and forth over the walls of the how to check if overweight, simulates the gobble or squawk of the bird.

Measure an 8-inch-byinch rectangle for the bottom and two 8-inch-byinch rectangles for the sides of the box caller. The paddle is about 2 inches longer because it has a handle.

Cut out the rectangles for the bottoms and sides. The tops of the sides are curved, and there are many methods for creating the arched shape. Note that, at this point, the sides are half an inch taller than the finished depth of the box. Make a paper template with an arch shape that is 2 inches tall at each end with a 2. Use the template to cut the curved top. This must be precise, as the sides must match for the call to work.

Sand the curved edges smooth. Use the Dremel tool with the sanding disk to create a channel, or groove, on each of the long sides of the bottom piece. This step is optional if you want to simply nail or glue the sides to the bottom. Use the scrap lumber to make a block for the inside of each end of the box. Measure the inside dimensions of the box and cut a block of that width, about 2 inches thick. Run a bead of glue along the bottom of one of the sides and insert the side into the slot in the base.

Repeat with the other side. Wipe up any drips of glue. Put glue on the bottom of the end blocks, and glue them into place. They should be flush with the ends of the sides. You should now have a rectangular box with sides that arch in the middle and no top. The underside of the handle typically is curved so the finished product looks like a cross section of a bottle — flat on one side and curved on the other.

Use a belt sander to create the effect. Make a 2-inch-long handle on one end of the paddle. Traditional box turkey call handles have an oval shape at the free end that pinches in near the box or two inverted arcs. Trace the shape onto the end of the paddle and cut it skylanders giants dragonfire cannon what does it do. Finish the assembly.

Drill a hole in the square end of the paddle about a half inch from the end and centered side to side. Make sure that when you insert the screw, it will hit the end block. Insert the screw partway and slip the spring onto the screw inside the box. Finish screwing the paddle onto the box.

Experiment with moving the paddle back and forth across the box until you achieve the right sound. You can make the box and the paddle from the same wood, but the quality of the call may not be as good.

Try walnut with walnut or cedar with cedar. She has extensive experience in tent and RV camping, hiking, backcountry exploration and cycling. Related How to Make a Magpie Trap. Build your turkey call box with any kind of wood you like. If you choose cherry, you can find cheap cabinet cherry wood at a hardware or lumber store.

Your first turkey call box may not be your best. Once you build a few, you will learn how to build a better turkey call box for the sound you want.

Step 1: Design Proposal

top edge of the sound boards and try operating the call. If you do not get a good two-tone yelp, dropping from high to lower pitch, try loosening the adjustment screw slightly. Apr 17,  · Most turkey hunters know how to go about turkey calling. Turkey calling is by far not the most critical element of a hunt, but it is critical that you get it Author: O.F. Mossberg & Sons, Inc.

For my final project, I would like to construct a turkey box call. The box of the call will be constructed of mahogany with birch ends. The paddle will be constructed of Purple Heart. The bottom of the box will be made out of birch and mahogany ends to match the box. The moving part will be the paddle.

The first step in making a box call is selecting your wood. It is best to use a soft wood for the box and a harder wood for the paddle that has a nice straight grain to make tuning easier. This step helps with the final tone of the call.

The Idea is to have opposite grain direction for the paddle and the box. The results of this little test will determine the front and rear of the box, as well as the screw end or handle of the paddle.

Do the same for the box part but it will be opposite of the paddle. If it grabs From A to B put the screw in the A end. Glue those together and let set for the given amount of time. Next were ready to cut the angles for the sides of the box.

I used 5 degrees for my box. Try to keep the bottom of the box at around 1" wide. I'm going to be putting some purple heart inlay into the box. Set your fence to wherever you would like the inlay on the box, and cut the mortise for the inlay on both sides. Place the vertical inlay over the glued part of the mahogany and birch. Cut out pieces of purple heart to fit in the inlays and glue.

Now your ready for checkering on both sides of the box. I'll first draw the pattern on the sides. I did this to make the call different from other checker patterns, and I would encourage you to come up with a design that you can call your own. You can experiment with different ideas until you find one that you like. I don't checker all of my calls, but when I do, I use this pattern as my signature for my calls. The checkering is not only for looks. It also makes the call a little easier to tune.

It allows the sides of the box to vibrate when running the paddle across the sound boards. This will mean less material you will need to remove from the inside walls to achieve the sound you want. Use a razor blade to do this. Your ready to hollow out the inside of the box to create the sound chamber.

Mark the top of my box where you want to hollow out. Use a small sanding block to smooth up the inside but don't take off too much material leave that step for the tuning process. Create a channel at the rear of the box for the paddle. You can use a sharp knife, sanding disk or wood file, whatever works best for you. I've chosen Purple Heart for my paddle and the end grain is very close to what I'm looking for.

It will work out fine. I need to rip down the blank to the thickness I want for the paddle. Determine the front and rear then cut the handle out from the front. You can also have the option of putting inlays in to the top of the paddle. I choose to put mahogany inlays in mine to match the box. I also wood burned a design on top of the box which is also optional.

Glue those together you can cut them to size after it dries. Your ready to put a radius on the bottom of the paddle.

I've drawn the radius on the end of the paddle to give me an Idea where I need to be when I cut the paddle and begin to sand it to shape. You can take it straight to the belt sander or angle the table saw to get a head start on the sanding. The screw hole will depend on the size screw you use. Drill the hole at the front of the box call. Set your paddle on top of the box and place a mark where you need to drill your hole.

If you have a different size spring you can change bits to match the spring. Use a sanding block made with a scrap piece of wood form the first step. Lay the call on it's side and work the sanding block back and fourth along the inside top edge of the soundboards.

All you want to do is round over the edge at this point. I'm not removing any other wood inside the call. I leave a little flat spot along the top rails and the thickness will be adjusted once we start tuning the call. Glue the bottom of the box on to the top and once that is dry you can put a 45 degree angle on the sides for a nice look. Once both sides are rounded over, it's time to put the paddle on the box. Put your spring and screw in place and screw down the paddle.

When looking at the side of the call with the paddle in the open position as if you're starting a yelp. The paddle should rest at the center of the box or just in front of center. Give the paddle a few strokes with pressure. It may take a few tries until you can get any sound from the call.

If you do get a sound it's most likely going to be a high pitch squeal at first. If you're lucky If not Try not to remove any more along the top edge of the sound boards at this point.

Keep checking the sound as you go, you will be surprised how much the sound changes with removing a small amount. If you can't grasp the sides of the soundboard and flex them a little bit by squeezing Keep going back and fourth with this process until your getting a good sound.

Here are a few tips you should know about tuning the box call. If you taper the sides of the box, so that the front of the sound boards are thicker than the rear, it will. Adjust the side thickness. If you're still having trouble getting a good sound, try sanding the underside of the paddle and the top. If box call is tuned, finish sanded down to grit and ready for your favorite finish coat. I used a satin polyurethane finish, but you can use whatever finish you would like but make sure you tape off the sound board top edges and the underside of the paddle that makes contact with the box you don't want to get any finish on those areas.

Once the call is completely done you can chalk the lid with box call chalk or carpenters chalk if you would like. I just touch up the underside of the paddle and the box call rails Very Lightly with grit sand paper if needed.

During the duration of this project I learned new ways to use some of the wood machines. Such as I learned how to use the table saw to make channels for the inlays on my box and paddle. I also learned how to angle the band saw to put a 5 degree angle on the box. I would like to learn if there is an easier and more efficient way to make the box call.

I would like to know a way to make the top angle cut on the box so it is perfect and even, and the 5 degree angle on the sides. I excelled at learning how to use the machines I needed to make the proper cuts. I excelled at thinking each step through to make sure I would end up with the product I needed.

I also excelled at getting a realistic sound out of the box and had a gobbler answer to the call. I would do a lot differently. I would make an outline for the paddle and the top curve so that it would be a perfect curve and handle. I would so find something to place on the band saw in order to keep the box even on the 5 degree side cuts. Also I would wood burn the crosses into the sides instead of trying to cut them out. I would make the cuts more even and precise. I would also leave more of an arch on the top to allow for a smoother sound.

I would make the sound hole wider to allow for a deeper less high pitched yelp. My favorite part of this project was hearing that gobbler answer back to my call after my brother had used several of his and he would not answer. I loved seeing the final product and knowing I worked really hard to get to that point. It was not an easy project at times and I learned many things from having to problem solve.

I think if I had some templates of the paddle handle and the arch on the box I could start making some to sell. I really enjoyed making a project that I would use and be proud of. Thicker sides equals higher pitch 2. Thinner sides equals lower pitch 3.

3 thoughts on “How to make turkey box call

  1. Take notes Capcom. This is the result of actually putting effort into your fighting game for launch.

Add a comment

Your email will not be published. Required fields are marked *